Purpose: Resets the settings for all remote controls associated with the vehicle.

WARNING: After completing this procedure, all remote controls will be deleted and will need to be reprogrammed using the “How to Program a Remote Control” tutorial .

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 46 – Comfort Module“.

4 – Click on “Adaptation – 10”.

5 – Select Channel 00

Set the value to 0 and save

L’article Toledo (5P) – Resetting the Remote Controls est apparu en premier sur VAG Coding.

Purpose: Allows you to program the remote controls that will be used with the vehicle for central locking and unlocking.

WARNING: This procedure does not allow you to program the remote controls with the vehicle’s immobilizer.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 46 – Comfort Module“.

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 ( “Remote Control Adaptation” from the drop-down list)

Enter the number of keys to program, then click Save.
Next, press the Unlock button on each remote control to be programmed for at least 1 second. The flashing lights will confirm the procedure.
All keys must be programmed in a single session, one after the other.
Programming all keys must not take longer than 15 seconds.
You can add up to 4 remote controls. If the [Test] and/or [Save] buttons are grayed out and unclickable, the module likely has all 4 slots filled; delete the remote controls using the “Reset Remote Controls” tutorial.

L’article Toledo (5P) – Programming a Remote Control est apparu en premier sur VAG Coding.

Purpose: Allows you to correct the fuel consumption display on the onboard computer.

Modification possible uniquement sur les modèles Milieu/Haut de gamme.
Remarque: les modifications apportées ont une incidence sur l’affichage de la consommation instantané, de la consommation moyenne, et de la quantité de carburant.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “ Select,” then click “17 – Instruments.”

4 – Click “Adaptation – 10.”

5 – Select Channel 03 “Consumption Correction”

Set the consumption correction factor between 85% and 115% (base value: 100)

Example 1: Calculation based on volume per distance (e.g., l/100 km): Specified: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9.8 / 9.73 ? 105.38) Channel 3 will be changed from 100 to 105
Example 2: Calculation based on distance per volume (e.g., MPG): Target: 23 MPG. Actual: 24 MPG. (100, 23/24, and 95.83) Channel 3 will be changed from 100 to 96

L’article Toledo (5P) – Fixed the OBD fuel consumption display est apparu en premier sur VAG Coding.

Purpose: Allows you to adjust the power steering stiffness for a smoother or stiffer, sportier steering feel.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “44 – Power Steering” / “44-steering assist.”

4 – Click “Adaptation – 10“

5 – Select Channel 1, then enter a value between 1 and 15 based on your preferred hardness level

Or Line 2: (If Channel 1 is unavailable):

3 – Click “Select,” then click “44 – Power Steering” / “44-steering assist.”

4 – Click on “Coding – 07“

5 – Choose :

• xxx1x for smooth steering
• xxx2x for a sporty ride
• xxx3x for a stiff steering feel
• xxx4x for a firmer steering feel
• xxx5x for very stiff steering

L’article Toledo (5P) – Adjusting the Power Steering Firmness est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for Seat Toledo (5P)
–> Buy your OBDeleven device with VAG Custom

Seat Toledo 5P (2005-2009)

• Activate Bluetooth RNS315
• Bending lights
• Daytime running lights
• DRL parameters
• ESC V2 deactivation
• Heating test
• Unlocking the heater
• Oil service reset
• Engine oil type

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps TOLEDO list (5P) est apparu en premier sur VAG Coding.

Purpose: to activate the hidden menu in RNS 315.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Adaptation – 10”.

5 – Select Developer mode (temporary) then set the value to Enabled

Restart RNS 315.

To launch the Hidden Menu, press SETUP (for 6s)

L’article Toledo (5P) – Activate hidden menu RNS 315 est apparu en premier sur VAG Coding.

Purpose: to activate Bluetooth on the RNS 315.

ATTENTION: Not all RNS-315 are equipped with a Bluetooth module.

You can also remove the RNS 315 from its slot to check. Behind it, you’ll find a label with the RNS-315’s MAC address.
If the MAC address contains only zeros (MAC: 00:00:00:00:00:00), your RNS-315 is not equipped with the Bluetooth module.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 3
Bit 5: Uncheck the “Telephone Transceiver inactive” box

L’article Toledo (5P) – Activate Bluetooth on RNS 315 est apparu en premier sur VAG Coding.

Purpose: Allows you to add a Driving School mode view to the RCD 210, RCD 310 that displays turn signals, speed … (Also ideal for accompanied driving)


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“56 – Radio”.

4 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Channel 2”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“1” and confirm.

L’article Toledo (5P) – Activate Driving School mode (RCD 210/RCD 310) est apparu en premier sur VAG Coding.

Purpose : Selects the language used in the on-board computer.

(Modification only possible on Mid/High range models)

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 04

Change the value according to the desired language

00001 – German
00002 – English
00003 – French
00004 – Italian
00005 – Spanish
00006 – Portuguese / Brazilian

L’article Toledo (5P) – Change ODB language est apparu en premier sur VAG Coding.

Purpose: To suppress the audible alarm and the warning light on the speedometer when driving without a seatbelt.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on “Coding 07”.

5 – The third and fourth coding digits (xx??x0x) are used to modify Instrument module options. To suppress the belt alarm, subtract 2 from these digits.

In the example above, the initial coding (with belt alarm) is: 0023103

To delete the belt alarm, simply recode as follows: 0021103 (23 – 02 = 21)

L’article Toledo (5P) – Delete belt alarm est apparu en premier sur VAG Coding.