Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of frost. (Origin: 4°C)
Then choose“Outsitde temperature p ice warning exit temperature” for the value at which the frost alert ends. (Origin: 6°C)

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Tarraco (KN) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: to display oil temperature on the Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“10”
Then check Bit“1”:“Display Oil Temperature”.

L’article Tarraco (KN) – Oil temperature on Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: to modify and customize the Active Info Display / Virtual Cockpit. Depending on the setting, the display of the counter and/or vmax is different.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 (To change counter background) :

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the “Tube illustration” / “Tube representation” channel.

6 – In the “Value:” option, select one of the following versions:

Version 0

Version 1

Version 2

Version 3 (Cupra bronze):

Version 8: Cupra

For Sport Cupra central counter see tuto :

Line 2 (To modify Vmax) :

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the “Tachometer end value” channel.

6 – In the “Value:” option, choose one of the 3 versions:

Version 0 – 260 km/h
Version 2 – 240 km/h
Version 3 – 300 km/h

L’article Tarraco (KN) – Changing the Virtual Cockpit display est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Tarraco (KN) – Front Assist settings est apparu en premier sur VAG Coding.

Purpose: To deactivate the roller blind comfort function when locking/unlocking.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 (Deactivate roller blind when comfort is locked) :
The roof roller shutter is closed when the comfort system is closed. You can adjust this behavior so that the roof roller shutter remains in the current position.

3 – Click on “Select”, then click on “CA – Open roof”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“IDE11842-MAS13330-Komfortfunktionen-Komfortschließen Dachrollo” /“Comfort functions – Roof blind comfort closure”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose “No Active”. No Active “then confirm.

Line 2 (Deactivate roller blind when comfort is opened):
The roof roller shutter is opened when the comfort system is opened. You can adjust this behavior so that the roof roller shutter remains in the current position.

3 – Click on “Select”, then click on “CA – Open roof”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“IDE11842-MAS13329-Komfortfunktionen-Komfortöffnen Dachrollo” /“Comfort functions – Comfort opening roof blind”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select “No Active” and confirm.

L’article Tarraco (KN) – Deactivate roller blind when locking/unlocking est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display in the Virtual Cockpit.

Note: these changes affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel: “Display correction of consumptions and operating range”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96.

Example 3: the consumption announced by the ODB is 5.9l/100km, after checking it is actually 6.3l/100km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%, and the consumption announced by the ODB will be a pessimistic 0.1l/100km.

Consumption is immediately modified on the MMI.

L’article Tarraco (KN) – Correction of Virtual Cockpit fuel consumption display est apparu en premier sur VAG Coding.

Purpose: to keep the 3rd brake light on if the trunk is not fully closed. For security lighting at night or to make sure your safe is securely closed.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte22BR MA57-Lichtfunktion C 22”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, select the value“Heckdeckel Offen” and confirm. (Origin: nicht aktiv)


Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte22BR MA57-Dimmwert CD 22”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“100” depending on the power of the brake light, then confirm. (Origin: 0)

L’article Tarraco (KN) – Third brake light on when trunk is open est apparu en premier sur VAG Coding.

Purpose: turns on license plate illumination when trunk / tailgate is open.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 25KZL HA59 – Lichtfunktion C 25”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, choose the value“Heckdeckel Offen” and confirm. (origin : nicht aktiv)


Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 25KZL HA59 – Dimmwert CD 25”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“100” and confirm. (origin : 0)

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte25KZL HA59 – Dimming Direction CD 25”.

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On the latter, choose“maximise” then validate.

L’article Tarraco (KN) – License plate illumination, open trunk est apparu en premier sur VAG Coding.

Purpose: activates window operation (close/open) with ignition off and door open.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Access control 2-Freigabenachlauf FH bei Kl 15 aus”.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, select“active”, then confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Access control 2-Freigabenachlauf FH bei Tueroeffnen abbrechen”.

7 – On the same page, there’s a second drop-down menu at the bottom of the page.
On this menu, select“not active”, then confirm.

L’article Tarraco (KN) – Activate window operation with ignition off est apparu en premier sur VAG Coding.

Purpose: automatically unlocks all doors when the DSG automatic gearbox is shifted to “P”.

Procedure:
1– Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

3 – Click on “Select” then click on “09 – Cent. Elect.”.

4 – Click on “Security Access – 16” then enter the code “31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Access control – Autounlock NAR”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, choose “active”, then confirm.

L’article Tarraco (KN) – Automatic door unlocking with DSG in “P” position est apparu en premier sur VAG Coding.