Purpose: to activate fog lamps when reversing.

Watch out! There are 4 lines of coding to do here.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12NL LB45-Lichtfunktion C 12“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Rueckfahrlicht” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12NL LB45-DimmwertCD12“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“100” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13NL RB5-Lichtfunktion C 13“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Rueckfahrlicht” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13NL RB5-DimmwertCD13“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“100” and confirm.

D12 and D13 if C12 and C13 are already active, 127 instead of 100 if you have LED ABs.

L’article Leon (5F) – Activate fog lamps when reversing est apparu en premier sur VAG Coding.

Purpose: to provide headlight flashes with the reversing lights (to warn drivers who are too close to you).

Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte28RFL LC11-Lichtfunktion B 28“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Lichthupe generell” and confirm.

Line 2 (Option to increase the intensity of the reversing light) :

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte28RFL LC11-Dimmwert AB 28”.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, select“100” for Halogens or“127” for LEDs, then confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64-Lichtfunktion B 29“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Lichthupe generell” and confirm.

Line 4 (Option to increase the intensity of the reversing light) :

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64-Dimmwert AB 29”.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, select“100” for Halogens or“127” for LEDs, then confirm.

L’article Leon (5F) – Headlight call with reversing lights est apparu en premier sur VAG Coding.

Purpose: activates rearview mirror defrosting automatically when rear window defrosting is activated, to avoid having to move the rearview mirror switch to set defrosting, for example when in position R for reversing.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“: “Rear window heater trigger, active“


Line 2:

3 – Click on“Select”, then click on“42 – Driver’s door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“:“Rear window heater trigger, active“.

L’article Leon (5F) – Activate automatic defrosting of rearview mirrors with rear window est apparu en premier sur VAG Coding.

Purpose: activates the parking lights on both sides of the vehicle, instead of the default single-side activation via the turn signal switch. Practical for improving night-time visibility when the vehicle is parked on the side of the road.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Außenlicht_uebergreifend-Parklicht ueber LSS aktiviert”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select “Bilateral” and confirm.

L’article Leon (5F) – Activate parking lights on both sides est apparu en premier sur VAG Coding.

Purpose: to activate or deactivate the 2-cylinder mode message on the on-board computer for vehicles equipped with the cylinder deactivation option (1.4 TSI ACT).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Cylinder shut-off” / “désactivation des cylindres”.

6 – On the same page, there’s a second drop-down menu at the bottom of the page.
Select“Display” or “ No Display” and confirm.

L’article Leon (5F) – 2-cylinder mode display on ODB est apparu en premier sur VAG Coding.

Purpose: enables headlight flashes to be made even when the ignition is off.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Driving light and parking light-Lichthupe bei Zuendung aus moeglich”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Leon (5F) – Contactless headlight activation est apparu en premier sur VAG Coding.

Goal: Add fog lamps for Coming Home and Leaving Home in addition to LEDs and Xenon.

Warning! There are 5 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Comfort illumination-Coming Home Leuchten”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Low Beam” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 12NL LB45-Lichtfunktion E 12”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Coming Home oder Leaving home Aktiv” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 12NL LB45-Dimmwert EF 12”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“100” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 13NL RB5-Lichtfunktion E 13”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Coming Home oder Leaving home Aktiv” and confirm.

Line 5:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 13NL RB5-Dimmwert EF 13”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“100” and confirm.

L’article Leon (5F) – Coming / Leaving Home with fog lamps, Xenon and LEDs est apparu en premier sur VAG Coding.

Purpose: to adjust the ACC distance setting from the factory setting so that it can be set in 1 km/h increments by pressing the switch.

By default, the PLUS and MINUS buttons on the adaptive cruise control system adjust your speed in 10 km/h increments. You can change the coding in 1 km/h increments by briefly pressing the button. And use the old 10 km/h speed increments by pressing and holding the buttons.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Select bit 6 “Operation Mode 2”.

Some speed controller modules may use a different coding or even have this parameter as an adaptation instead of the coding. Make sure that the option you are about to modify is correctly labeled.

Module 13 → Adaptation → Mode de fonctionnement / Operation Mode → Mode de fonctionnement 2 / Operation Mode 2

L’article Leon (5F) Facelift – Set ACC control in 1 km/h increments est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Leon (5F) Facelift – Front Assist settings est apparu en premier sur VAG Coding.

Purpose: to set the distance between the kerb and the car during Park Assist.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“10 – Park/Steer Assist” / “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Abstand zum Bordstein” / “Distance to curb” / “Ecart avec la bordure”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the distance you prefer (in cm). Default value“15cm” then validate.

L’article Leon (5F) – Increase distance between curb and car (Park Assist) est apparu en premier sur VAG Coding.