Purpose: to activate the speed regulator after retrofitting.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “01 – Motor”.

4 – Click on “Access – 11” then enter the code “11463”

L’article Leon (1P) – Cruise control activation (retrofit) est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display on the on-board computer.

Modification only possible on Mid/High range models.
Note: modifications affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel 03 “Consumption Correction”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96

L’article Leon (1P) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose : to adjust the hardness of the power steering for a softer or harder steering wheel.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“44 – Direction assistée” / “44-steering assist.

4 – Click on“Adaptation – 10”.

5 – Select Channel 1 , set a value between 1 and 15 depending on your hardness preference.

Or Line 2: (If channel 1 is unavailable):

3 – Click on“Select” then click on“44 – Direction assistée” / “44-steering assist.

4 – Click on“Coding – 07”.

5 – Select :

• xxx1x for smooth steering
• xxx2x for sports management
• xxx3x for hard steering
• xxx4x for harder steering
• xxx5x for very hard steering

L’article Leon (1P) – Modify power steering hardness est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera after installation on the RCD 510/330/360/440 and RNS 315/510 (retrofit).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 3
Then check bit 6 “Rear View Camera (RVC) installed/active”.

Line 2 (Option, if parking assistance available) :

3 – Click on“Select”, then click on“10 – Assistance Stationn”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 0
Then check bit 5 “Rear View Camera installed”.

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article Leon (1P) Facelift – Activate rear view camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Leon (1P) Facelift – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Leon (1P) Facelift – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: To suppress the audible alarm and the warning light on the speedometer when driving without a seatbelt.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 1: “Seatbelt warning active/installed”.

L’article Leon (1P) Facelift – Remove alarm belt est apparu en premier sur VAG Coding.

Purpose: to activate voice control on the RNS 510 (SDS).

ATTENTION: RNS 510 firmware must be version v2660.

Activating voice control brings up the “Voice control” menu in the RNS 510’s SETUP menu.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 3, check the box for“Bit 1: Microphone Diagnostics active”.

Byte 7, uncheck the box for“Bit 1: Voice Control inactive”.

To install the microphone, connect the microphone lead to the rear of the RNS 510. Connect to pins (Mic-)C1 and (Mic+)C7.

L’article Leon (1P) Facelift – Activate RNS 510 voice control est apparu en premier sur VAG Coding.

Purpose: Enables fog lamps to be used for Coming Home and Leaving Home.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 17:
Bit 3: Check “Coming-Home (CH) via Fog-Light active”.

L’article Leon (1P) Facelift – Coming / Leaving Home with fog lamps est apparu en premier sur VAG Coding.

Purpose: Activates xenon headlamps instead of fog lamps for Coming Home and Leaving Home.

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 17 :

Bit 3: Uncheck “Coming-Home (CH) via Fog-Light active”.

L’article Leon (1P) Facelift – Coming / Leaving Home with Xenons est apparu en premier sur VAG Coding.