Purpose: Enables Apple CarPlay Wireless and Google Android Auto Wireless to be activated without the need for a USB cable.

Vehicle must have an active USB wired CarPlay connection (from SW 1803, SFD: yes)

Warning! There are 8 lines of coding to do here.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or OBDeleven.

2 – Switch on the ignition and run the VCDS program. or OBDeleven.

Line 1 (Wifi):


3 – Click on ” Select ” then click on “Select”.5F – Information Electr.” .

4 – Click on “Adaptation – 10”.

5 – Choose Channel : “function_configuration_connectivity – wifi_client_mode_5GHz”.

Set value to “ON

Line 2 (Wifi):


3 – Click on ” Select ” then click on “Select”.5F – Information Electr.” .

4 – Click on “Adaptation – 10”.

5 – Choose Channel : “function_configuration_connectivity – wifi_client_mode_2_GHz”.

Set value to “ON

Line 3 (Wifi):


3 – Click on ” Select ” then click on “Select”.5F – Information Electr.” .

4 – Click on “Adaptation – 10”.

5 – Select Channel : “function_configuration_connectivity – WIFI_Hotspot_5GHz”.

Set value to “ON

Line 4 (Wifi):


3 – Click on ” Select ” then click on “Select”.5F – Information Electr.” .

4 – Click on “Adaptation – 10”.

5 – Choose Channel : “function_configuration_connectivity – WIFI_Hotspot_2_4GHz”.

Set value to “ON

Line 5 (Apple Carplay wireless):


3 – Click on ” Select ” then click on “Select”.5F – Information Electr.” .

4 – Click on “Adaptation – 10”.

5 – Choose Channel : “function_configuration_connectivity – apple_car_play”.

Set value to “ON

Line 6 (Android Auto wireless):


3 – Click on ” Select ” then click on “Select”.5F – Information Electr.” .

4 – Click on “Adaptation – 10”.

5 – Choose Channel : “function_configuration_connectivity – google_android_auto”.

Set value to “ON

Line 7 (App Connect):


3 – Click on ” Select ” then click on “Select”.5F – Information Electr.” .

4 – Click on “Adaptation – 10”.

5 – Select Channel : “function_configuration_connectivity – app_connect_over_wifi”.

Set value to “ON

Line 8 (Option):


3 – Click on ” Select “, then click on “Select”.5F – Information Electr.” .

4 – Click on “Adaptation – 10”.

5 – Select Channel : “function_configuration_connectivity – wlan_module”.

Set value to “ON

Restart MIB3, reset MIB3 (hold down volume control for at least 10-15 seconds)

Don’t plug your Apple device into the USB port!

Make sure the WIFI access point is enabled in the MIB3 settings.
On your iPhone under Settings -> Wi-Fi, your car should appear with ***_5GHZ.
Pair your Apple device with Bluetooth, it should now ask if you want to enable CarPlay.
If not, delete the pairing, connect to the car’s Wi-Fi first from the Apple device, then try pairing again via Bluetooth.

L’article Formentor (KM7) – Wireless CarPlay activation est apparu en premier sur VAG Coding.

Purpose: Activate the Ambient Light option on your MIB3 to change the 30 colors.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.


Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior_light_hmi_config – Hmi_ambient_colors_bitmask”.

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On this, choose“7F FF FF FF FF” then validate.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior_light_hmi_config – Hmi_contour_colors_bitmask”.

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On this, choose“7F FF FF FF FF” then validate.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior_light_hmi_config – Hmi_ambient_colors_fod_bitmask”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“3F FF FF FF FF” then validate.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior_light_hmi_config – Hmi_contour_colors_fod_bitmask”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“3F FF FF FF FF” then validate.

OBDeleven:

Full coding :

Interior_light_general_settings:
Automatic_ambiance_lighting_with_fpa active

Interior_light_hmi_config:
Hmi_ambient_colors_bitmask 45140AD
Hmi_contour_colors_bitmask 45140AD
Hmi_ambient_colors_fod_bitmask 3FFFFFFF
Hmi_contour_colors_fod_bitmask 3FFFFFFF
Hmi_setup_set_1 13
Hmi_setup_set_2 7
Hmi_setup_set_3 15
Hmi_setup_set_4 5
Hmi_setup_members_set_1_byte_2 1C
Hmi_setup_members_set_2_byte_3 60
Hmi_setup_members_set_3_byte_3 10
Hmi_setup_members_set_4_byte_1 C
Hmi_setup_members_multi_color_byte_1 C
Hmi_setup_members_multi_color_byte_2 1C
Hmi_setup_members_multi_color_byte_3 70
Hmi_config_member_center_color_scheme_1 3
Hmi_config_member_center_bottom_color_scheme_1 3
Hmi_config_member_bottom_color_scheme_1 3
Hmi_config_member_center_color_scheme_3 3
Hmi_config_member_center_bottom_color_scheme_3 2
Hmi_config_member_bottom_color_scheme_3 2
Hmi_config_member_center_color_scheme_6 3
Hmi_config_member_center_bottom_color_scheme_6 2
Hmi_config_member_bottom_color_scheme_6 3
Hmi_config_member_center_color_scheme_8 3
Hmi_config_member_center_bottom_color_scheme_8 3
Hmi_config_member_bottom_color_scheme_8 2
Hmi_menu_ambient_lighting active
Hmi_ambient_color active
Hmi_contour_color active
Hmi_ambient_profile_1 active
Hmi_ambient_profile_2 active
Hmi_ambient_profile_3 active
Hmi_ambient_profile_4 active
Hmi_ambient_profile_5 active
Hmi_ambient_profile_6 active
Hmi_ambient_profile_7 active
Hmi_ambient_profile_8 active
Hmi_fpa_dependency active
Hmi_functional_ambience_lighting active
Hmi_play_of_colors active
Hmi_Display_Color_light_function 1

Interior_light_router_config:
Output_lin5_light_function_slave_3 7
Output_lin5_light_function_slave_4 8
Output_lin5_light_function_slave_8 17
Output_lin5_light_function_slave_9 18
Output_lin5_light_function_slave_11 4
Output_lin5_light_function_slave_12 5
Output_lin9_light_function_slave_2 D
Output_lin9_light_function_slave_3 E
Output_lin9_light_function_slave_6 12
Output_lin9_light_function_slave_7 12
Output_lin10_light_function_slave_3 9
Output_lin10_light_function_slave_4 A
Output_lin10_light_function_slave_8 19
Output_lin10_light_function_slave_9 1A
Output_lin10_light_function_slave_11 4
Output_lin10_light_function_slave_12 5

Interior_light_functions_1_to_70:
Light_function_1 active
Light_function_4 active
Light_function_5 active
Light_function_7 active
Light_function_8 active
Light_function_9 active
Light_function_10 active
Light_function_13 active
Light_function_14 active
Light_function_18 active
Light_function_23 active
Light_function_24 active
Light_function_25 active
Light_function_26 active

L’article Formentor (KM7) – Ambient Light activation (30 colors) est apparu en premier sur VAG Coding.

Purpose: to adjust seat heater temperature levels. Note that temperature values for individual steps must be set in ascending order.
Please check the number of seat heating levels your vehicle supports before changing. Not all vehicles support levels 1 to 6.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose :

Seat_Heating_Level_Adaptation:

• Seat_heating_stage_1_lower_threshold: 20,0°C (stage 1)
• Seat_heating_stage_1_upper_threshold: 20,5°C (stage 1)
• Seat_heating_stage_2_lower_threshold: 20,0°C (stage 1)
• Seat_heating_stage_2_upper_threshold: 20,5°C (stage 1)
• Seat_heating_stage_3_lower_threshold: 33,0°C (stage 2)
• Seat_heating_stage_3_upper_threshold: 33.5°C (stage 2)
• Seat_heating_stage_4_lower_threshold: 33,0°C (stage 2)
• Seat_heating_stage_4_upper_threshold: 33.5°C (stage 2)
• Seat_heating_stage_5_lower_threshold: 50,0°C (stage 3)
• Seat_heating_stage_5_upper_threshold: 50,5°C (stage 3)
• Seat_heating_stage_6_lower_threshold: 50,0°C (stage 3)
• Seat_heating_stage_6_upper_threshold: 50,5°C (stage 3)

OR

• “IDE06089-ENG263544-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_1_lower_threshold”
• “IDE06089-ENG263507-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_1_upper_threshold”
• “IDE06089-ENG263592-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_2_lower_threshold”
• “IDE06089-ENG263559-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_2_upper_threshold”
• “IDE06089-ENG263539-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_3_lower_threshold”
• “IDE06089-ENG263539-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_3_lower_threshold”
• “IDE06089-ENG263536-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_4_lower_threshold”
• “IDE06089-ENG263549-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_4_upper_threshold”
• “IDE06089-ENG263566-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_5_lower_threshold”
• “IDE06089-ENG263597-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_5_upper_threshold”
• “IDE06089-ENG263562-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_6_lower_threshold”
• “IDE06089-ENG263524-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_6_upper_threshold”

6 – On this same page, there’s a second drop-down menu, but at the bottom
of the page.
Adjust the values as required. “Lower” is the activation temperature and “higher” is the deactivation temperature.

L’article Formentor (KM7) – Adjust temperature of heated seats est apparu en premier sur VAG Coding.

Purpose: to display a compass on the Active Info Display / Virtual Cockpit (AID).

SFD: no

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or OBDeleven.

2 – Switch on the ignition and run the VCDS program. or OBDeleven.

Line 1:

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the “navigation_compass” channel.

6 – In the “Value:” option, select“Enabled”.

L’article Formentor (KM7) – Compass display on Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: to activate the closing and opening of the windows and sunroof with the KESSY keyless entry system. press and hold the handle until the windows are fully closed or open.

SFD: yes

Warning! There are 5 lines of coding to do here.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Kessyfunktion – Komfortbedienung_fh_oeffnen_ueber_kessy”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Komfort_Fensterheber – Komfortbedienung_fh_oeffnen_ueber_sz”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Komfort_Fensterheber – Komfort_oeffnen”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 4:

3 – Click on“Select”, then click on“B7 – Access Startsystem Interface”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Passive_Komfort – Passive_Komfort_Oeffnen_aktiv”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 5:

3 – Click on“Select”, then click on“B7 – Access Startsystem Interface”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Passive_Komfort – Passive_Komfort_Togglen_aktiv”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

L’article Formentor (KM7) – Opening/closing windows with KESSY est apparu en premier sur VAG Coding.

Purpose: to deactivate the active ignition alert when the engine is running or a door is open.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Unterdrückung Zündungswarnung – Ausgabe MoLaWa_AAW”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select “Deactivated” and confirm.

L’article Formentor (KM7) – Deactivate active ignition warning with engine running/door open. est apparu en premier sur VAG Coding.

Purpose: to activate the heartbeat or lighting power of the Start Engine Stop button for the keyless start option.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 (Lighting power):

3 – Click on“Select”, then click on“B7 – Access authorization/startup”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“DevCod_ Search lights – Suchbeleuchtung_ZAT_Beleuchtung_SES_Variante_aktiv”.

7 – On the same page, there is a second drop-down menu at the bottom
of the page.
Select“Active” (LED = dim) or“not_activated” (LED = bright) and confirm.

Line 2 (Pulse):

3 – Click on“Select”, then click on“B7 – Access authorization/startup”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“DevCod_ Search lights – Suchbeleuchtung_ZAT_SES_Mode”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“Active” (LED flashing) or“not_activated”. (LED = on) then confirm.

L’article Formentor (KM7) – Engine start button pulse est apparu en premier sur VAG Coding.

Purpose: Adds a driving-school mode view to the MIB3, displaying turn signals, speed, etc. (also ideal for accompanied driving).

SFD: yes


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or your OBDeleven box.

2 – Switch on the ignition and run the VCDS program. or the OBDeleven application. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations – menu_display_driving_school”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations – menu_display_driving_school_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Formentor (KM7) – Activate driving-school mode est apparu en premier sur VAG Coding.

Purpose: deactivates the beep when reverse gear is engaged in DSG position R.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Acoustics_driving_position_R” / “Acoustics: Rapport R”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select “Not Active” and confirm.

L’article Formentor (KM7) – Deactivate DSG reverse beeper est apparu en premier sur VAG Coding.

Purpose: deactivates or activates the horn when the ignition is off.

SFD: yes


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“LIN_SMLS_konfig_2_Signalhornbetatigung”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Klemme 15 an” to deactivate it, then confirm.

L’article Formentor (KM7) – Deactivate horn without ignition est apparu en premier sur VAG Coding.