Purpose: to set confirmation of door locking/unlocking with beep (alarm) or horn.

SFD: yes

Watch out! There are 5 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Quittierton_global“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.


Line 2:

3 – Click on“Select” then click on “.19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Akustische Quittieringsdauer Einfachhorn”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this, choose“normal” or“kurz” (for a short signal), then confirm.


Line 3:

3 – Click on“Select” then click on “.19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Quittungston_hmi_einstellbar“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on “.19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Quittierungston_bei_entriegeln“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 5:

3 – Click on“Select” then click on “.19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Quittungs_ton_bei_verriegen“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Born (K11) – Door lock/unlock confirmation (beep/horn) est apparu en premier sur VAG Coding.

Purpose: to unlock the limitations of Android Auto, allowing access to all functions without the restrictions imposed by default on the multimedia system.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.8125 – Application Server Infotainment“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“nhtsa_properties – nhtsa limitation switches for androidauto no text input”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 2:

3 – Click on“Select” then click on “.8125 – Application Server Infotainment“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“nhtsa_properties – nhtsa limitation switches for androidauto no voice input”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

L’article Born (K11) – Unlock Android Auto limitations est apparu en premier sur VAG Coding.

Purpose: automatically activates the high beam assistant on start-up if it was active before the ignition was switched off.

SFD: yes


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“High Beam Assistance – Fernlichtassistent Reset“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“not active” and confirm.

L’article Born (K11) – Light Assist always active est apparu en premier sur VAG Coding.

Purpose: Enables you to unlock certain multimedia system menus while driving, which are normally blocked when the vehicle is in motion.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.8125 – Application Server Infotainment“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Locked menu contents“.

7 – On this same page is a second drop-down menu, but at the bottom
of the page.
On this, choose“non_blocked” then validate.

L’article Born (K11) – Unlock menus while driving est apparu en premier sur VAG Coding.

Purpose: to display fan speed when automatic climate control mode is activated (Climatronic fan speed display Auto mode / works with touch-sensitive climate control).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC”.

4 – Unlock SFD protection.

5 – Click on ” Adaptation – 10 “.

6 – Select ” blower display in auto operation ” in the value list

7 – Select ” activated ” from the second value list

L’article Born (K11) – Displays fan speed on air conditioning in Auto mode est apparu en premier sur VAG Coding.

Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights switch on and off immediately with the headlights. Activating this function will cause a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.19- Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Suchbeleuchtung_allgemein – KL58 Einschalten mit Rampe“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article Born (K11) – Activates progressive interior lighting est apparu en premier sur VAG Coding.

Purpose: to deactivate the daytime running lights (DRL) using the handbrake.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.19- Gateway“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Daytime running lights-Tagfahrlicht Dauerfahrlicht bei Handbremse abschalten“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Born (K11) – Daytime running light deactivation (DRL) with handbrake on est apparu en premier sur VAG Coding.

Purpose: Adjusts the sensitivity of the light sensor.

SFD: yes

Procedure:
1– Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or your OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

3 – Click on “Select”, then click on “09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “RLS_Night_Sensitivity – p_lx_rs_dawn”.

7 – On this same page, there is a second drop-down menu, at the bottom
of the page.
On this, choose the sensitivity value in lux, then confirm. (default: 200 lx) (The lower the value, the sooner the headlights come on).

L’article Born (K11) – Set light sensor sensitivity est apparu en premier sur VAG Coding.

Purpose: Selects the speed at which the radar and/or reversing camera are deactivated.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“76 – Assistance stationnt“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Switch-off speed for parking assist“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“15” km/h, depending on your preference.

L’article Born (K11) – Speed of radar (or reversing camera) deactivation est apparu en premier sur VAG Coding.

Purpose: to deactivate the beep when reverse gear is engaged or when parking assistance is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or your OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on ” Select” then click on ” 76 – Assistance stationnt ” .

4 – Unlock SFD protection.

5 – Click on ” Adaptation – 10 “.

6 – Select ” Tonalité d’activation de l’aide au stationnement ” / ” Park assist activation tone ” / ” Aktivierungston für Einparkhilfe ” from value list

7 – Select ” Off” in the second value list

L’article Born (K11) – Deactivation of parking aid activation beep est apparu en premier sur VAG Coding.