Purpose: Displays the “Driving Mode” on the Easy Connect MIB2. This may need to be enabled after replacing the MIB if the driving modes are no longer available.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma_over_threshold_high“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17_msg_bus“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Infotainment data bus” and then confirm.

L’article Ateca (5F) – Driving Mode on MIB2 est apparu en premier sur VAG Coding.

Purpose: Allows you to adjust the ACC distance setting from the factory setting so that it can be adjusted in 1 km/h increments by pressing the switch.

By default, the PLUS and MINUS buttons on the adaptive cruise control adjust your speed in 10 km/h increments. You can change the setting to 1-km/h increments by briefly pressing the button. To use the previous 10-km/h speed increments, press and hold the buttons.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:


3 – Click “Select,” then click “ 13 – Regular Distribution “.

4 – Click “Security Access – 16,” then enter the code “14117 or 2010 3 ”

5 – Click on “Coding – 07”

6 – Click “ Long Coding Helper.”

7 – Select Byte 02

Select bit 6, “Operation Mode 2”

Some cruise control modules may use different coding or even have this setting configured via adaptation instead of coding. Make sure the option you are about to change is correctly labeled.

Module 13 → Adaptation → Operation Mode → Operation Mode 2

L’article Ateca (5F) – Adjust the ACC setting in 1 km/h increments est apparu en premier sur VAG Coding.

Purpose: activates rearview mirror defrosting automatically when rear window defrosting is activated, to avoid having to move the rearview mirror switch to set defrosting, for example when in position R for reversing.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“: “Rear window heater trigger, active“


Line 2:

3 – Click on“Select”, then click on“42 – Driver’s door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“:“Rear window heater trigger, active“.

L’article Ateca (5F) – Activate automatic mirror defrosting with rear window est apparu en premier sur VAG Coding.

Purpose: activates the parking lights on both sides of the vehicle, instead of the default single-side activation via the turn signal switch. Practical for improving night-time visibility when the vehicle is parked on the side of the road.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Außenlicht_uebergreifend-Parklicht ueber LSS aktiviert”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select “Bilateral” and confirm.

L’article Ateca (5F) – Activate parking lights on both sides est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Ateca (5F) – Front Assist settings est apparu en premier sur VAG Coding.

Purpose: cancels the coupling of roller blinds and panoramic sunroofs, allowing them to be adjusted separately.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or your OBDeleven box.

2 – Switch on the ignition, then run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“CA – Sunroof”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“02”
Then uncheck Bit“6”.

L’article Ateca (5F) – Deactivate coupling between roller blind and sunroof est apparu en premier sur VAG Coding.

Purpose: To deactivate the roller blind comfort function when locking/unlocking.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 (Deactivate roller blind when comfort is locked) :
The roof roller shutter is closed when the comfort system is closed. You can adjust this behavior so that the roof roller shutter remains in the current position.

3 – Click on “Select”, then click on “CA – Open roof”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“IDE11842-MAS13330-Komfortfunktionen-Komfortschließen Dachrollo” /“Comfort functions – Roof blind comfort closure”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose “No Active”. No Active “then confirm.

Line 2 (Deactivate roller blind when comfort is opened):
The roof roller shutter is opened when the comfort system is opened. You can adjust this behavior so that the roof roller shutter remains in the current position.

3 – Click on “Select”, then click on “CA – Open roof”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“IDE11842-MAS13329-Komfortfunktionen-Komfortöffnen Dachrollo” /“Comfort functions – Comfort opening roof blind”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select “No Active” and confirm.

L’article Ateca (5F) – Deactivate roller blind when locking/unlocking est apparu en premier sur VAG Coding.

Purpose: deactivates sound reduction when reverse gear is engaged or parking aid is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Adaptation – 10”.

6 – Select “Demande réduction audio ” / “Audio attenuation request” / “Anforderung Audioabsenkung ” from the value list.

7 – Select “Off” in the second value list

L’article Ateca (5F) – Disable audio reduction for parking assistance est apparu en premier sur VAG Coding.

Purpose: turns on license plate illumination when trunk / tailgate is open.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 25KZL HA59 – Lichtfunktion C 25”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, choose the value“Heckdeckel Offen” and confirm. (origin : nicht aktiv)


Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 25KZL HA59 – Dimmwert CD 25”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“100” and confirm. (origin : 0)

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte25KZL HA59 – Dimming Direction CD 25”.

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On the latter, choose“maximise” then validate.

L’article Ateca (5F) – License plate illumination, open trunk est apparu en premier sur VAG Coding.

Purpose: automatically retracts the electric driver’s seat when the ignition is switched off and the door is opened (access aid).

This option can only be activated with a VCDS with experimental coding for the lo coding wizard.ng! (MIB2 compatible)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on “.36 – Seat Mem. Drvr“.

4 – Click on“Coding 07”.

5 – Select “Long coding wizard”:

Byte 3, Set bit 1 – “Easy_Entry_front,0=nict aktiv/1=aktiv

For passenger seat with electric option: Byte 6, Set bit 3

Then Byte 9 Set bit 6 – “automatic_func_key_memory_over_MMI, 0=nict aktiv/1=aktiv”.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2 – driver_seat_0x10”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2 – driver_seat_0x10_msg_bus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Comfort data bus” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2 – menu_display_seat_configuration”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2 – menu_display_seat_configuration_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Ateca (5F) – Easy Entry est apparu en premier sur VAG Coding.