Purpose: Resets the settings for all remote controls associated with the vehicle.

WARNING: After completing this procedure, all remote controls will be deleted and will need to be reprogrammed using the “Program a Remote Control” tutorial .
If your vehicle is equipped with a KESSY remote control (05 – Access/Start Authorization), you cannot delete the remote controls using this procedure.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “ “09 – Cent. Elect.”.”

4 – Click on “Adaptation – 10”.

5 – Select Channel 00

Set the value to 0 and save

L’article A3 (8P) Facelift – Resetting the Remote Controls est apparu en premier sur VAG Coding.

Purpose: Allows you to program the remote controls that will be used with the vehicle for central locking and unlocking.

WARNING: This procedure does not allow you to program remote controls with the vehicle’s immobilizer.
If your vehicle is equipped with a KESSY remote control (05 – Access/Ignition Authorization), you cannot program a new remote control using this procedure.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “ “09 – Cent. Elect.”.”

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 ( “Remote Control Adaptation” from the drop-down list)

Enter the number of keys to program, then click Save.
Next, press the Unlock button on each remote control to be programmed for at least 1 second. The flashing lights will confirm the process.
All keys must be programmed in a single session, one after the other.
Programming all keys must not take longer than 15 seconds.
You can add up to 7 remote controls. If the [Test] and/or [Save] buttons are grayed out and unclickable, the module likely has all 7 slots filled; delete the remote controls using the “Reset Remote Controls” tutorial.

L’article A3 (8P) Facelift – Programming a Remote Control est apparu en premier sur VAG Coding.

Purpose: Resets the settings for all remote controls associated with the vehicle.

WARNING: After completing this procedure, all remote controls will be deleted and will need to be reprogrammed using the “How to Program a Remote Control” tutorial .

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 46 – Comfort Module“.

4 – Click on “Adaptation – 10”.

5 – Select Channel 00

Set the value to 0 and save

L’article A3 (8P) – Resetting the Remote Controls est apparu en premier sur VAG Coding.

Purpose: Allows you to program the remote controls that will be used with the vehicle for central locking and unlocking.

WARNING: This procedure does not allow you to program the remote controls with the vehicle’s immobilizer.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 46 – Comfort Module“.

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 ( “Remote Control Adaptation” from the drop-down list)

Enter the number of keys to program, then click Save.
Next, press the Unlock button on each remote control to be programmed for at least 1 second. The flashing lights will confirm the procedure.
All keys must be programmed in a single session, one after the other.
Programming all keys must not take longer than 15 seconds.
You can add up to 4 remote controls. If the [Test] and/or [Save] buttons are grayed out and unclickable, the module likely has all 4 slots filled; delete the remote controls using the “Reset Remote Controls” tutorial.

L’article A3 (8P) – Programming a Remote Control est apparu en premier sur VAG Coding.

Purpose: Allows the rear fog lamps to be used when reversing, giving more light and safety when maneuvering in the dark.

Modification only possible for vehicles with a 30-byte module.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on “Select” then click on “09 – Cent. Elect.” .

4 – Click on “Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

6 – Byte 26:
Check Bit 6

L’article A3 (8P) – Activate fog lights when reversing est apparu en premier sur VAG Coding.

Purpose: to activate the gear display on the on-board computer (for manual gearboxes).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on ” 10 – Adaptation

5 – Select Channel 36 “Special Functions”
Add +1 to the existing value as specified in the tooltip (?xx).

Example: original value 000: change to 100

So excluding S/RS, the only possible value is: 100

L’article A3 (8P) Facelift – Gear display on ODB est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on “Coding 07”.

5 – The third and fourth coding digits (xx??x0x) are used to modify Instrument module options. To remove the ice-washer indicator, subtract 1 from these digits.

In the example above, the initial coding (with washer indicator) is: 0023103

To delete the windscreen washer indicator, simply recode as follows: 0022103 (23 – 01 = 22)

L’article A3 (8P) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer, for A3 8P phase 1 only).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on “Coding 07”.

5 – The third and fourth coding digits (xx??x0x) are used to modify Instrument module options. To remove the ice-washer indicator, subtract 4 from these digits.

In the example above, the initial coding (with washer indicator) is: 0025103

To remove the windscreen washer indicator, simply recode as follows: 0021103 (25 – 04 = 21)

L’article A3 (8P) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Audi A3 (8P)
–> Buy your OBDeleven device with VAG Custom

Audi A3 8P (2003-2012) / Audi S3 / RS3 (facelift) / A3 8P Facelift (specific facelift coding at bottom of page)

• Instrument cluster area
• Oil service reset
• RNS-E start-up screen
• Activate daytime running lights
• Automatic locking/unlocking
• Activate AUX input
• CD/DVD eject lock
• CH/LH lights
• Change language
• Comfort operation for sliding roofs
• Daytime running lights
• DRL with fog lights
• Emergency brake lights
• Floor lighting
• Headlamp washer
• Heated mirrors
• Inspection service reset
• Acoustic and visual confirmation of locking/unlocking
• Optical parking system
• Seat belt warning
• Synchronized mirror adjustment
• Tourism solution for lighthouses
• Engine oil type

Audi A3 8P Facelift (2008-2012)

• ESC V2 deactivation
• High beam assistant by region (LHD/RHD)
• High beam assistant city recognition
• High beam speed threshold
• Inspection service reset
• Low beam speed threshold
• Oil change reset
• RNS-E start-up screen
• DRL low beam
• Automatic locking/unlocking
• Automatic reverse wiping
• Activate AUX input
• CD/DVD eject lock
• Central locking with IGN
• CH/LH lights
• Change language
• Comfort function for sunroof
• Comfort flashing light
• Take-home mode
• Time to return home
• Bending lights
• Bending lights with reverse
• DRL activation/deactivation
• Attenuation DRL
• DRL parameters in the dashboard
• DRL with ADL
• DRL with fog lights
• Emergency brake lights
• Fog lamps with high beam
• Floor lighting while driving
• Headlamp washer
• Heated mirrors
• V2 inspection service reset
• Instrument cluster region
• Departure time
• LED license plate lamps
• Horn lock/unlock confirmation
• Optical parking system
• Rear window wiper
• Rear window wiper
• Remote window function
• Seat belt warning
• Selective central locking
• Synchronized mirror adjustment
• Drop-shaped windshield wiper
• Windshield wiper control
• Engine oil type
• Multimedia security notice
• Disabling the Start/Stop system

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps A3 list (8P) est apparu en premier sur VAG Coding.

Purpose : to display the speed limit on the RNS-E navigation screen.

ATTENTION: requires RNS-E version 193

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on “Select”, then click on“37 – Navigation”.

4– Click on“Adaptation – 10”.

5 – Select Channel 17 (Speed Display) then set the value according to the desired display.

Set the value according to the desired display
0– no option (display disabled)
1– option on, off (speed display)
2– option on, off, 5km/h, 10km/h, 15km/h, 20km/h (speed display + overrun warning)

Don’t forget to restart the RNS-E, by pressing the power button for more than 40s.

L’article A3 (8P) Facelift – Speed limit display RNS-E est apparu en premier sur VAG Coding.