Purpose: to adjust the logic of the AWD system to increase traction or reduce noise generated by the Haldex AWD mechanism. (For TT Quattro / TTS)

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“22 – AWD”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Logique” /“Logic”.

6 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On this, choose the value according to your preference:

• “Standard”
• “Increased Traction
• “Less Noise

then validate.

L’article TT (8S) – Haldex traction adjustment est apparu en premier sur VAG Coding.

Purpose: deactivates sound reduction when reverse gear is engaged or parking aid is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Adaptation – 10”.

6 – Select “Demande réduction audio ” / “Audio attenuation request” / “Anforderung Audioabsenkung ” from the value list.

7 – Select “Off” in the second value list

L’article TT (8S) – Deactivate audio reduction for parking assistance est apparu en premier sur VAG Coding.

Purpose: to set the value in minutes of the heating reduction time for heated seats. As a general rule, Audi vehicles reduce the heat output of level 3 seat heating to level 2 after 10 minutes. It is also possible to activate the return from level 2 to level 1.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Time until seat heating reduction level 3 to level 2” /“Zeit bis Sitzheizleistungsrücknahme Stufe 3 auf Stufe 2” (also for 2 to 1).

6 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose the value in minutes (0 = function disabled) then validate.

L’article TT (8S) – Seat heater reduction time setting est apparu en premier sur VAG Coding.

Purpose: to disable spoiler operation. If you code the spoiler deployed or closed, it will be locked in the position after coding! Perfect for mounting a fixed tuning spoiler.

Procedure:
1– Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2– Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Zusatzfunktionen – Tt_Spoiler” or “Allwetterlicht – Tt_Spoiler”.

7 – On the same page, you’ll find a second drop-down menu (Origin: elektrisher spoiler)
On this menu, select“feststehender spoiler” to keep it fixed.
Or, to completely disable aileron operation for a fixed aileron installation, select “Not installed”.

OR

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on “Coding – 07” then click on “Long Coding Helper”.

5 – Choose Byte 02:
Bit 5-6: Select : “feststehender spoiler”

L’article TT (8S) – Deactivate aileron est apparu en premier sur VAG Coding.

Purpose: to activate an alarm with horn in the event of intrusion into the vehicle, and to lock the door if it is opened. (after 2015)

Warning! There are 8 lines of coding to do here.

For vehicles without original alarm!

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Additional functions – Signalhorn ohne KL 15”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“active” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Anti-theft protection – Akustischer Alarm Signalhorn”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“active” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Anti-theft protection – Alarmsignal”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“frequency modulated” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Anti-theft protection – DWA Alarmverzoegerung”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this menu, select“driver door contact thatcham” and confirm.

Line 5:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Anti-theft protection – DWA Camper Modus”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“active” and confirm.

Line 6:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Protection antivol – Sirenen Alarmzahl”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“10 alarms” and confirm.

Line 7:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Protection antivol – Verzoegerung Panikalarm”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
Select“2 sekunden verzoegerung” and confirm.

Line 8:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Anti-theft Alarm System” Anti-theft Alarm System

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“active” and confirm.

L’article TT (8S) – Activate intruder alarm with horn est apparu en premier sur VAG Coding.

Purpose: to activate closing and opening of windows and sunroof with the KESSY keyless entry system, keep pressing the handle until the windows are fully closed or open.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Access control 2-Kessy Komfort oeffnen”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Access control 2-Kessy Komfort schliessen”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

L’article TT (8S) – Opening/closing windows with KESSY est apparu en premier sur VAG Coding.

Purpose: Allows you to connect two phones simultaneously via Bluetooth to the MMI if you don’t have the Audi Phone Box option.




Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Vehicle configuration – Support_second_phone”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart MMI

L’article TT (8S) – Activate a second phone via Bluetooth est apparu en premier sur VAG Coding.

Purpose: deactivates or activates the horn when the ignition is off.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Additional functions – Signalhorn ohne KL 15”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, choose“not active” to deactivate it or “active” to activate it, then confirm.

L’article TT (8S) – Deactivate horn without ignition est apparu en premier sur VAG Coding.

Purpose: deactivates the beep when the Audi Parking System is engaged.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Adaptation – 10”.

6 – Select “Tonalité d’activation de l’aide au stationnement ” / “Park assist activation tone ” / “Aktivierungston für Einparkhilfe ” from value list

7 – Select “Off” in the second value list

L’article TT (8S) – Deactivation of Audi Parking System engagement beep est apparu en premier sur VAG Coding.

Purpose: deactivates interior lighting when only the trunk is opened.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior lighting Innenlicht-bei offenem Heckdeckel einschalten”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“inactive” and confirm.

L’article TT (8S) – Interior lighting deactivated when trunk is opened est apparu en premier sur VAG Coding.