Purpose: to adjust Bluetooth microphone sensitivity with Audi MMI 3G.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

To continue, you must first activate the hidden MMI menu (Green Menu).

To activate the MMI hidden menu (Green Menu) : Activate MMI 3G Hidden Menu

Press CAR + SETUP for 6 sec to bring up the hidden menu.

main > diagnostics > settings > Mic sensiblity

Choose a value between : -6db/0db/+6db

Restart MMI

Simultaneously press SETUP (1) + Central knob (2) + Top right knob (3)

L’article Q5 (8R) – Microphone sensitivity adjustment est apparu en premier sur VAG Coding.

Purpose: to deactivate automatic activation of the rear windshield wiper during reversing when the front windshield wipers are operating.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “09 – Cent. Elect.” . Switch on the ignition and run the VCDS program. 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Security Access – 16” then enter the code“20113”.

4 – Click on “Adaptation – 10” .

5 – Select Channel 19 from the drop-down list

To deactivate, select value 0

L’article Q5 (8R) – Deactivate rear wiper when reversing est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera after installation (retrofit camera standard aftermarket or dynamic line camera with camera high module).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 (Camera standard and high):

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 35
Then check Bit 4: “Parking Aid: Rearview Camera installed/active via BCM1 [PR-7X7/7X8]”.

If bit 4 is hidden, in the hexa (yellow digit) if you have 24, change to 34.

Line 2 and 3 only for High camera with module in trunk!

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 7
Then check Bit 1: “Menu Back Up Camera Active”.

Line 3:

3 – Click on“Select” then click on“19 – CAN Gateway”.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Reboot MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed under the screen (Audi Multimedia).

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 11 = video line
Pin 5 = shielding

L’article Q5 (8R) Facelift – Activate reversing camera (retrofit) est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Audi Q5 (8R)
–> Buy your OBDeleven device with VAG Custom

Audi Q5 8R (2008-2017) / Audi SQ5 / Q5 8R Facelift (specific facelift coding at bottom of page)

• Brake pad replacement
• Comfort windows
• Bending lights
• DRL function with flashing light
• DVD lock MMI 2G
• MMI 3G DVD lock
• Efficiency program
• Emergency brake lights
• 3G/3G+ engineering menu
• Euro parking lights
• Garage door openers
• Gauge test – Needle sweep
• 2G green engineering menu
• Headlamp washer
• Unlocking the heater
• Lighting
• Inspection service reset
• Stopwatch
• Lock/unlock confirmation
• Mirror scan
• MMI 3G/3GP radio frequency
• MMI 3G/3GP video on the move
• Oil service reset
• Optical parking system
• Automatic release of parking brake
• Retrofit front lights Q5
• Remove the electric handbrake without braking
• Scandinavian DRL
• Seat belt warning
• Service interval
• Shift paddles
• Side marker lights
• Soundaktor
• Reverse on/off button
• On/off function
• NAR tail lights to EU
• Travel mode in MMI
• Bluetooth and AUX for Concert 3
• Deleting a Bluetooth device
• Type of CH light activation
• CH/LH lights
• CH/LH light variant
• CH/LH menu setting
• Correction of consumption display
• Door exit lights
• Daytime running lights on/off
• Main unit daytime running light settings
• Motor 1 fan test
• Motor 2 fan test
• Engine start message
• Foot lighting
• Foot lighting while driving
• Fuel system priming
• Number of headlamp washer activations
• Headlamp washer activation delay
• Headlamp washer activation time
• Heated mirrors
• Hill-start assist
• Interior door handle lighting
• MMI 3G start-up screen
• Multifunction display
• Speed warning
• Teardrop wipe
• Climate control display
• Engine oil type
• Engine preheating

Audi Q5 8R Facelift (2012-2017)

• Additional DS modes
• Brake pad replacement
• Comfort windows
• Bending lights
• MMI drive selection
• DRL function with flashing light
• MMI 3G DVD lock
• Efficiency program
• Emergency brake lights
• 3G/3G+ technical menu
• Euro parking lights
• Garage door openers
• Gauge test – Needle sweep
• Headlamp washer
• Unlocking the heater
• Lighting
• Inspection service reset
• Stopwatch
• LED license plate lamps
• Lock/unlock confirmation
• Mirror scan
• MMI 3G/3GP Radio frequency
• MMI 3G/3GP Video on the move
• Oil service reset
• Scandinavian DRL
• Seat belt warning
• Service interval
• Shift paddles
• Side marker lights
• Soundaktor
• Reverse on/off button
• On/off function
• Summer menu in MMI
• Rear lights NAR to UE
• Bluetooth and AUX for Concert 3
• Door exit lights
• DRL activation/deactivation
• Motor Fan test 1
• Motor 2 fan test
• Fog lamps with high beam
• Floor lighting
• Floor lighting while driving
• Fuel system priming
• Interior door handle lighting
• Open door alarm
• Brake pad warning
• Central locking with IGN
• DRL with fog lights
• Engine oil type
• Engine preheating
• Multimedia restart

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps Q5 (8R) list est apparu en premier sur VAG Coding.

Purpose: To modify and/or customize the Splash Screen logo with a personalized image of the MMI 3G and 3GPLUS.

Start by downloading the script file: MMI_3G_3GP_SplashScreen_VAG-Coding.en.zip

Proceed :

• Then extract the file you just downloaded: MMI 3G 3GP SplashScreen VAG-Coding.en.zip
• Go to the “splashscreens” folder and edit the “startup_generic.png” image if you wish. You can edit this image, modify it or import another image, to have your own startup logo (keep the same PNG format and image size 800×480) or an image found in the “samples” folder (copy it into the “splashscreens” folder with the name startup_generic.png.
• Copy the contents of the MMI_3G_3GP_SplashScreen folder to a FAT32-formatted SD card (max. 32GB).
• Start your AUDI and let the MMI boot up, it takes a few seconds.
• Disconnect your smartphone’s Bluetooth if there’s a link between it and the MMI, and remove all your SD cards (SD1 & SD2)…
• Then insert the SD card you have prepared into slot SD1.
• You’ll see green text asking you to turn the large knob on your MMI central console, and the message will disappear.
• Wait a few moments. A new message will appear stating that all has gone well and that your image has been imported successfully.
• Restart the MMI using the button combination that corresponds to your AUDI.
  Example: Press SETUP or MENU (1) + Central knob (2) + Top right button (3) at the same time.

If your new start-up screen does not appear when your MMI reboots, go to the green hidden menu (to activate the hidden menu, follow the “Activate MMI 3G or 3GP hidden menu” tutorial).

For MMI 3GP : Select in car -> carcodingvehicle -> Select n° screen -> set cursor to 0, then restart your MMI.

For MMI 3G: car -> carcodingvehicle -> configuration line -> [standard] 2/5 (Standard home screen) then restart your MMI.

Your very own Splash Screen will appear!
Many images are available in the zip file… both the original and modified ones.

A problem? If the script doesn’t run the first time, try again. You’ve only copied the contents of the MMI_3G_3GP_SplashScreen folder? Do not copy the folder, just its contents!
For MMI 3G Basic: If your image does not appear or is truncated, resize the image to 400 by 240.

L’article Q5 (8R) – MMI 3G/3GP customized start logo est apparu en premier sur VAG Coding.

Purpose: to deactivate/activate the electric handbrake in maintenance mode in order to change/replace the rear brake pad/disc linings. (EPB reset / Lining change mode)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


To start, set the gear lever to P, remove the electric handbrake on the button and preferably connect a battery charger according to the vehicle manual. Check that there are no faults/errors before starting basic setup.

3 – Click on“Select” then click on“53 – Parking Brake”.

4 – Click on“Basic setting – 04”.

5 – Select Channel 007

6 – Click on“Go”.

Basic Settings: OFF during the procedure, then ON when finished (yellow arrow).

A fault message will appear on your ODB indicating“Parking brake fault” and an LED in the parking brake switch, but this is normal and should be ignored.

7 – Once finished, go back (Done, Go Back) until the program closes.

8 – Switch off the vehicle’s ignition, then disconnect the VAG-COM cable

9 – Change the linings on both sides!

To reactivate the electric handbrake :


10 – With engine off and ignition switched off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

11 – Switch on the ignition and run the VCDS program.

12 – Click on“Select” then click on“53 – Parking Brake”.

13 – Click on“Basic setting – 04”.

14 – Select Channel 006

15 – Click on“Go”.

Basic Settings: OFF during the procedure, then ON when finished (yellow arrow).

16 – Once finished, go back (Done, Go Back) until the program is closed.

17 – Switch off the ignition and disconnect the VAG-COM cable.

L’article Q5 (8R) – Deactivate/activate electric handbrake for rear brake pad change est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display on the on-board computer.

Modification only possible on Mid/High range models.
Note: modifications affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel 03 “Consumption Correction”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96

L’article Q5 (8R) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose: Allows you to add a driving-school mode view on the MMI Radio Concert / Symphony, which displays speed (also ideal for accompanied driving)


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“56 – Radio”.

4 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Channel 2” “Driving School Function/Time Display”.

7 – Set value to 1.

To activate the function, select SETUP -> settings -> driving school/speed

L’article Q5 (8R) – Display speed on the MMI est apparu en premier sur VAG Coding.

Purpose: to set the speed thresholds for activation/deactivation of the high beam assistant (light assist).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Adjust high beam assistant activation speed threshold :

3 – Click on ” Select”, then click on “Select”.20 – High beam wizard” .

4 – Click on “Adaptation – 10”.

5 – Select Channel :“ High beamvariation speed” or “Aktivierungsgeschwindigkeitfür Fernlichtassistent”.

Adjust value accordingly
Default: 57 km/h

Adjusting the high beam assistant deactivation speed threshold :

3 – Click on ” Select”, then click on “Select”.20 – High beam wizard” .

4 – Click on “Adaptation – 10”.

5 – Select Channel : “Headlight dimming speed” or “Geschwindigkeitsschwelle für Fernlichtempfehlung”.

Adjust value accordingly
Default: 27 km/h

L’article Q5 (8R) – High beam assistant settings est apparu en premier sur VAG Coding.

Purpose: Enables fog lamps to be used for Coming Home and Leaving Home.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 6:
Check bit 5

L’article Q5 (8R) – Coming / Leaving Home with fog lamps est apparu en premier sur VAG Coding.