Purpose: To activate the reversing camera after it has been installed on the MMI RMC or 3GP.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway“.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Line 2:

3 – Click on“Select” then click on“6C – Rear view camera“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Coding:

1030015 = Automatic hitch, with APS+.

1000015 = RVC only

1020015 = APS+, without automatic coupler

1010015 = Automatic hitch, without APS+.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper“.

For MMI RMC :
6 – Select byte 6
Then set bit 2

For MMI 3GP:
6 – Select byte 7
Then set bit 1

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Car Function List BAP Gen2 – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Car Function List BAP Gen2 – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “Terminal 15“

Restart MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article A6 (C7) – Activate reversing camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to lower the air suspension for a lowered style.

Select“Auto” mode via the MMI (it must not be set to Dynamic, Comfort, etc.). Make sure the car is on level ground. Close the doors. If the doors open during this operation, the procedure will be interrupted. Make sure the car is not in towing or tire-change mode. Eventually set the car to“Neutral” and release the handbrake (remember, you’re supposed to be on level ground, so your A6/S6, A7/S7 C7/4G, A8 D4 won’t move).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” Select ” and run the VCDS program. 34 – Level Control” .

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”, take note of the 4 values entitled as :

“Body height, stops front wheel shell G”.

“Body height, rear wheel shell G”stop

“Body height, stops front wheel shell D”.

“Body height, rear wheel shell stop D”.

6 – Take the values you noted above, and add the desired dimensions in millimetres (mm) to each value, noting them down carefully on a sheet of paper…

Example of a 15mm front and 11mm rear lowering:

• Front Left: 392.80 -> 407.80
• Front right: 388.40 -> 403.40
• Left rear: 391.30 -> 402.30
• Right rear: 385.60 -> 396.60

Be aware that Audi has a lowering tolerance of 17mm at the front and 13 at the rear, from what I understand. You can go lower if you like, but if you lower it a bit more, it will affect other parts of the system, such as the cameras, adaptive speed, etc., so be careful.

7 – Press “RETURN” Then go to“04 – Basic settings”

IMPORTANT: Whatever you do, do not select“Reset all adaptations”, as this will not work, and will require a visit to the dealer.

8 – Select“Activate trim”, click“Go!”, wait for it to finish (should only take a second or 2, until it says “Not active”) and then press “Stop”.

9 – Select“Erase trim calibration”, click on“Go!”, wait for it to finish, you’ll see an error message in the central display (ODB) of your meters indicating “Air Suspension Dysfunction ” with its little yellow car logo (drawings) with a two-way arrow in the center of the car (drawing), don’t worry this is normal, you’ll see in the VCDS writing “Not active” and then press “Stop”.

10 – Select“Approach reference level“, click on“Go! This step will take about a minute, and your car will rise and fall during the process (you’ll hear whistling). Wait until it finishes, until it says “Not active” and then press ” Stop “, then ” End, Back “.

11 – Go to“10 – Adaptation” on the previous screen.

12 – Next, you’ll need to enter the new values you’ve defined with the help of step 4 on your documents for the different heights.

“Body height, stops front wheel shell G”.

“Body height, rear wheel shell G”stop

“Body height, stops front wheel shell D”.

“Body height, rear wheel shell stop D”.

Select them, one after the other, to enter the new value you’ve determined, and click on“Save”, then repeat the operation for the other three wheel heights.

Each time you enter a value, you should get a message indicating that it has been accepted.

13 – When you have completed the changes for all 4 wheels, select“Back”, and return to“04 – Basic settings” again.

14 – In the basic settings, select“Calibrate trim” and press“Go! Wait for “Not active”) and then press ” Stop “.

If you get an error in this step, either you’ve missed a step described above, or something has gone wrong.

15 – Select“Activate trim”, click on“Go!”, wait a few seconds until it says “Not active” and then press “Stop”, then “End, Return”.

16 – When you’ve finished, go to“02 – Fault codes” and clear the error codes.

Get out of the car and watch, wait a moment, and she’ll lower herself as you wished!

If you’d like to make another adaptation, forget all about the changes you’ve made previously, as they don‘t add to the previous ones, and cancel them out completely.

For example, you lowered the first time by 5mm on the value 392.80, refer to step 2 of this tutorial and repeat the various steps.

This brings your total to 397.80. You want a total reduction of 15mm. You’ll then enter 407.80 the second time, and lower it by a further 10mm on the second modification, bringing you to a total of 5+10=15mm.
I remind you that a “visible” and yet fairly safe lowering value is 17mm at the front and 13mm at the rear, at most. We strongly advise against going any lower.

L’article A6 (C7) – Lowering the pneumatic chassis est apparu en premier sur VAG Coding.

Purpose: to deactivate automatic activation of the rear windshield wiper during reversing when the front windshield wipers are operating. (A6 Avant)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “09 – Cent. Elect.” . Switch on the ignition and run the VCDS program. 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Security Access – 16” then enter the code“20113”.

4 – Click on “Adaptation – 10” .

5 – Select Channel 19 from the drop-down list

To deactivate, select value 0

L’article A6 (C7) – Deactivate rear wiper when reversing est apparu en premier sur VAG Coding.

Purpose: Allows automatic deactivation of the electric handbrake on start-up without having to fasten the seatbelt.

Only for vehicles with automatic gearbox.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“53-Station brake”.

4 – Click on“Security Access – 16” then enter the code“78713”.

5 – Click on“Adaptation – 10”. Then select “Seat belt buckle detection” from the drop-down list.

Set value to “not active

L’article A6 (C7) – Automatic deactivation of unbuckled electric handbrake est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Audi A6 (C7)
–> Buy your OBDeleven device with VAG Custom

Audi A6 C7 (4G) (4H) (2011-2018) / Audi S6 / RS6 / Allroad

2011-2015 :

• Additional DS modes
• Brake pad replacement
• Bending lights
• MMI drive selection
• MMI 3G DVD lock
• 3G/3G+ technical menu
• Technical menu for MIB
• RMC technical menu
• Euro parking lights
• Scanning the gauge test needle
• Headlamp washer
• Unlocking the heater
• Inspection service reset
• Stopwatch
• LED license plate lamps
• Lock/unlock confirmation
• Mirror scan
• MMI 3G/3GP radio frequency
• MMI 3G/3GP motion video
• Oil service reset
• Rear cover control
• Scandinavian daytime running lights
• Seat belt warning
• Shift paddles
• Side marker lights
• Soundaktor
• Reverse on/off button
• On/off function
• Summer menu in MMI
• Rear lights NAR to UE
• Moving video for RMC
• Remote control for windows and sunroof
• Motor OFF when door opens
• CH/LH via fog lights
• CH/LH via LED DRL
• Dashboard start screen
• DRL activation/deactivation
• DRL menu in MMI
• Motor 1 fan test
• Motor 2 fan test
• Floor lighting while driving
• Fuel system priming
• Garage door openers
• Repair RMC Languages EU
• Repair RMC Languages USA
• Teardrop wipe
• DRL function with flashing light
• Engine oil type
• Engine preheating
• Inspection service distance
• Inspection service interval
• Multimedia restart
• Oil change service distance
• Oil change service interval
• Open door alarm
• Moving video for MIB

2015-2018 :

• Brake pad replacement
• Technical menu for MIB
• RMC technical menu
• Euro parking lights
• Gauge test – Needle sweep
• Speed indicator
• Headlamp washer
• Unlocking the heater
• Inspection service reset
• Stopwatch
• Dim LED DRL with turn signal
• LED license plate lamps
• Lock/unlock confirmation
• Mirror scan
• MirrorLink on the move
• Oil service reset
• Alternative radio frequency
• Checking the rear cover
• Scandinavian DRL
• Seat belt warning
• Second phone support
• Shift paddles
• Side marker lights
• Soundaktor
• Reverse on/off button
• On/off function
• Moving video for MIB
• Moving video for RMC
• Remote control for windows and sunroof
• Motor OFF when door opens
• Additional DS modes
• CH/LH via LED DRL
• Correction of consumption display
• Dashboard start screen
• DRL activation/deactivation
• DRL menu in multimedia
• Dynamic emergency lights
• Fan motor 1 Test
• Fan motor 2 Test
• Floor lighting while driving
• Fuel system priming
• Heated steering wheel temperature
• MIB start logo
• Central locking with IGN
• Engine oil type
• Engine preheating
• Inspection service distance
• Inspection service interval
• Multimedia restart
• Multimedia security disclaimer
• Oil change service distance
• Oil change service interval
• Open door alarm
• Showroom mode

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps A6 (C7) list est apparu en premier sur VAG Coding.

Purpose: To modify and/or customize the home screen logo (Custom Splash Screen) with a personalized image of the MMI 3G and 3GPLUS.

Start by downloading the script file: MMI_3G_3GP_SplashScreen_VAG-Coding.en.zip

Proceed :

• Then extract the file you just downloaded: MMI 3G 3GP SplashScreen VAG-Coding.en.zip
• Go to the “splashscreens” folder and edit the “startup_generic.png” image if you wish. You can edit this image, modify it or import another image, to have your own startup logo (keep the same PNG format and image size 800×480) or an image found in the “samples” folder (copy it into the “splashscreens” folder with the name startup_generic.png.
• Copy the contents of the MMI_3G_3GP_SplashScreen folder to a FAT32-formatted SD card (max. 32GB).
• Start your AUDI and let the MMI boot up, it takes a few seconds.
• Disconnect your smartphone’s Bluetooth if there’s a link between it and the MMI, and remove all your SD cards (SD1 & SD2)…
• Then insert the SD card you have prepared into slot SD1.
• You’ll see green text asking you to turn the large knob on your MMI central console, and the message will disappear.
• Wait a few moments. A new message will appear stating that all has gone well and that your image has been imported successfully.
• Restart the MMI using the button combination that corresponds to your AUDI.
  Example: Press SETUP or MENU (1) + Central knob (2) + Top right button (3) at the same time.

If your new start-up screen does not appear when your MMI reboots, go to the green hidden menu (to activate the hidden menu, follow the “Activate MMI 3G or 3GP hidden menu” tutorial).

For MMI 3GP : Select in car -> carcodingvehicle -> Select n° screen -> set cursor to 0, then restart your MMI.

For MMI 3G: car -> carcodingvehicle -> configuration line -> [standard] 2/5 (Standard home screen) then restart your MMI.

Your very own Splash Screen will appear!
Many images are available in the zip file… both the original and modified ones.

A problem? If the script doesn’t run the first time, try again. You’ve only copied the contents of the MMI_3G_3GP_SplashScreen folder? Do not copy the folder, just its contents!
For MMI 3G Basic: If your image does not appear or is truncated, resize the image to 400 by 240.

L’article A6 (C7) – MMI 3G/3GP customized start logo est apparu en premier sur VAG Coding.

Purpose: Activates CD/DVD extraction in the DVD player. Allows you to import / copy all CD/DVD / SD card content to the MMI 3G PLUS jukebox (hard disk).

To continue, you must first activate the hidden MMI menu (Green Menu).

To activate the MMI hidden menu (Green Menu) : Activate MMI 3GP hidden menu

Press CAR + SETUP for 6 sec to bring up the hidden menu.

diagnose -> settings -> import_multimedia -> Tick Ripping

Restart MMI

Press MENU + Wheel + Top Right button.

L’article A6 (C7) – Enable MMI 3GP CD/DVD ripping est apparu en premier sur VAG Coding.

Purpose: Activates the speed limit display (traffic sign display) for the MMI 3G PLUS navigation system. The speed limit display appears in the navigation zone or on the navigation map, even without a camera system.

To continue, you must first activate the hidden MMI menu (Green Menu).

To activate the MMI hidden menu (Green Menu) : Activate MMI 3GP Hidden Menu

Press CAR + MENU for 6 sec to bring up the hidden menu.

Select diagnostics/coding/internal_modules_1+2/

Deactivate the “VZA (Off)” input (traffic sign display).

Restart MMI

Press MENU + Wheel + Top Right button.

After restart, the : Speed display (speed display) must be activated in the navigation area under Settings.
Speed limit information is then available and displayed on the navigation map view.

L’article A6 (C7) – Activate MMI 3GP speed limit display est apparu en premier sur VAG Coding.

Purpose: Set the length of time the headlights remain on after the car is unlocked / locked (Coming Home / Leaving Home).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select” then click on “09 – Cent. Elect.” .

4 – Click on “Adaptation – 10”.

5 – Select “Coming Home Leaving Home Zeitdauer” channel (Duration)

6 – Select duration from 0 to 60 seconds (in 1 sec increments). (Default: 15 sec)

L’article A6 (C7) – Coming Home / Leaving Home duration setting est apparu en premier sur VAG Coding.

Purpose: to activate the Coming Home / Leaving Home (CH/LH) function via the daytime running lights (DRL).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” Select ” and run the VCDS program.09 – Cent. Elect. “.

4 – Click on “Coding – 07” then click on “Long Coding Helper”.

5 – Select Byte 6 :

Disable Bit 4

L’article A6 (C7) – Coming Home / Leaving Home via daytime running lights (DRL) est apparu en premier sur VAG Coding.