Purpose: Allows the windows to be slightly ajar when the driver’s or passenger’s door is open. When a window is lowered, the cabin is no longer completely sealed, allowing the doors to be closed gently without having to slam them shut. (Windows Auto Drop)


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“


Line 2:

3 – Click “Select,” then click “42 – Driver’s Door.”

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“

L’article A5 (F5) – Enable automatic window lowering est apparu en premier sur VAG Coding.

Purpose: Enables the “recirculation” setting memory. If you have enabled it, it will remain active the next time the vehicle is started. Please note that your Audi has an automatic recirculation function via the MMI system; when this is enabled, the recirculation indicator light does not illuminate while the function is active.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC”.

4 – Click on “Adaptation – 10”.

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “IDE01476 – Store air recirculation setting with terminal 15 off“

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Storing” or “Save,” then confirm.

L’article A5 (F5) – Enable the air recirculation memory function est apparu en premier sur VAG Coding.

Purpose: Displays the intermediate km/h scale on the Virtual Cockpit speedometer. (Works only when the speedometer scale is set to km/h)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – instruments“.

4 – Click on“Coding – 07“, then on“Long Coding Helper“.

5 – Select byte “18“
. Then check bit “1“: “Tachometer_erweiterte_Skalenteilung”

OBDeleven: Tachometer_advanced_scale_division -> yes

L’article A5 (F5) – Display intermediate speeds in the Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: Allows you to unlock certain multimedia system menus while driving, and to enable text entry for CarPlay and Android Auto, which are normally disabled when the vehicle is in motion.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” Select “, then click on ” Select “. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.5F – Information Electr.” .

4 – Click “Adaptation – 10.”

Line 1 (Menu)

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Locked menu contents” (FB CAR, media , and nav)

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “non_blocked” and then confirm.

Line 2

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “NHSTA Properties“

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “not_activated” and then confirm.

Line 3 (CarPlay)

5 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_limitation_switches_for_carplay_no_softKeyboard“

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “not_activated” and confirm.

Line 4 (Android Auto)

5 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_limitation_switches_for_androidauto_no_text_input“

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “not_activated” and confirm.

L’article A5 (F5) – Unlock the menus while driving est apparu en premier sur VAG Coding.

Purpose: Disables the feature that automatically unlocks all doors when the DSG automatic transmission is shifted to the “P” position.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

3 – Click on “Select” then click on ” 46 – Central Module Comfort System “ .

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Clear the bit ” automatic_unlock_nar”

L’article A5 (F5) – Disable automatic door unlocking with DSG in “P” est apparu en premier sur VAG Coding.

Purpose: to deactivate/activate the electric handbrake in maintenance mode in order to change/replace the rear brake pad/disc linings. (Lining change mode)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


To begin, set the gearshift to P and remove the electric handbrake on the button. Check that there are no faults/errors before starting basic adjustment.

3 – Click on“Select” then click on“03 – ABS brake“.

4 – Click on“Basic setting – 04“.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Start trim change mode.“

6 – Click on“Go“.

A fault message will appear on your ODB indicating ” Parking brake fault“, but this is normal and should be ignored

7 – Wait for“Procedure complete” to be displayed

8 – Once finished, return to the program until it closes

9 – Switch off the vehicle’s ignition, then disconnect the VAG-COM cable

10 – Change the linings on both sides!

To reactivate the electric handbrake :


11 – With engine off and ignition switched off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

12 – Switch on the ignition and run the VCDS program.

13 – Click on“Select” then click on“03 – ABS brake“.

14 – Click on “Basic setting – 04“.

15 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“End trim change mode.“

16 – Click on“Go“.

17 – Wait for“Procedure complete” display

L’article A5 (F5) – Deactivate/activate electric handbrake for rear brake pad change est apparu en premier sur VAG Coding.

Purpose: to change the startup logo displayed on the Virtual Cockpit.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 9 and check the bits according to your preference:

Bit 0-2 select Variant :

L’article A5 (F5) – Virtual Cockpit start logo est apparu en premier sur VAG Coding.

Purpose: to activate the folding mirrors manually. Instead of the mirrors folding down on their own when the doors are closed, a long press on the remote control will be required, as for remote window closing.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on “.46 – Central Convenience”.

4 – Click on“Coding – 07”.

5 – Select byte 20
Then check Bit 4 “mirror_retractation_at_comfort_close”.

Note: The MMI system’s folding mirrors may NOT be activated. Once this option is activated, the mirrors fold instantly.

With the image setting, mirrors always fold immediately on locking

L’article A5 (F5) – Activate folding mirrors with remote control est apparu en premier sur VAG Coding.

Purpose: Activates the navigation screen display, allowing you to switch to the map display and display the navigation destination defined in the FARB-FIS (control panel).

However, the MuFuPlus steering wheel must be installed for the view in the FIS to be changed to a map. In addition, Google Maps will no longer be displayed on the navigation system in the MMI.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “5F – Electronic Information”.

4 – Click on“Adaptation – 10”

5 – Select channels :

• Change channel setting “ENG122230-ENG127005-Dashboard_Display_Configuration-navigation_map_transmission_mode” to “MOST_streaming”.

• Change channel setting “ENG122230-ENG122338-Dashboard_Display_Configuration-navigation_map_compression_mode” to “H264”.

• Change setting channel “ENG122230-ENG122339-Dashboard_Display_Configuration-navigation_map_resolution” to “resolution_1”.

Restart MMI

L’article A5 (F5) – Activate map display in PIS est apparu en premier sur VAG Coding.

Purpose: to remember the function of the Audi Lane Assist. If you deactivate it, the Lane Assist will not automatically resume the next time you start up.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “IDE07596-Personalisierung Spurhalteassistent bei Kl. 15 ein “/”Personalization of lane dept. warning Cl. 15 on“

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“last setting ” and confirm.

L’article A5 (F5) – Activate Lane Assist memory function est apparu en premier sur VAG Coding.