Purpose: to suppress navigation and telephone warning messages on the MMI when entering data while driving.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” Select “, then click on ” Select “. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.5F – Information Electr.” .

4 – Click on ” Adaptation – 10“.

5 – Select Channel 2 and 3 then set the value to 250.

L’article A5 (8T) – Disable NAV & Phone warning messages when entering while driving est apparu en premier sur VAG Coding.

Purpose: to deactivate the “Key not in vehicle” warning light
This message appears on the display with this symbol when you take the radio-controlled key out of the vehicle while the engine is running. This message is intended to remind you (e.g. when changing drivers) not to continue driving without the radio-controlled key.

If the radio key is no longer in the vehicle, you cannot switch on the ignition or restart the engine once the engine has been switched off. What’s more, you can’t lock the vehicle from the outside without the key.

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on“Select” then click on“46- Central Conv.

4 – Click on “Coding – 07” then “Long Coding Helper”.

5 – Select Byte 9:
Uncheck Bit 7

L’article A5 (8T) – Deactivate “Key not in vehicle” warning light est apparu en premier sur VAG Coding.

Purpose: to adjust Bluetooth microphone sensitivity with Audi MMI.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

For MMI 2G :

3 – Click on“Select”, then click on“77 – Telephone”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the top, there is a drop-down menu.
In this drop-down menu, choose Channel 131 or 07.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose a value expressed in“dB” (default value“0 dB”) then validate.

For MMI 3G :

To continue, you must first activate the hidden MMI menu (Green Menu).

To activate the MMI hidden menu (Green Menu) : Activate MMI 3G Hidden Menu

Press CAR + SETUP for 6 sec to bring up the hidden menu.

main > diagnostics > settings > Mic sensiblity

Choose a value between : -6db/0db/+6db

Restart MMI

Simultaneously press SETUP (1) + Central knob (2) + Top right knob (3)

L’article A5 (8T) – Microphone sensitivity adjustment est apparu en premier sur VAG Coding.

Purpose: to modify the brightness, contrast, saturation and temperature of the rear camera image.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on“Select“, then click on“6C – Rear View Camera“.

4 – Click on“Security Access – 16” then enter the code“22351“.

5 – Click on“Adaptation – 10“.

6 – Select channel to modify :

Channel 10 (Brightness)
Select a value between 1 and 100 (default: 50)

Channel 11 (Contrast)
Select a value between 1 and 100 (default: 50)

Channel 12 (Saturation)
Select a value between 1 and 100 (default: 50)

Channel 13 (Temperature)
Select a value between 1 and 100 (default: 50)

L’article A5 (8T) – Rearview camera settings est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 10:
Then uncheck Bit 0: “Brake Pad Wear Warning active”.

L’article A5 (8T) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 4: “Washer Fluid Warning active”.

L’article A5 (8T) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to activate engine preheating so that both the engine and the vehicle interior are heated. In the factory, only the vehicle interior is heated and there is no engine preheating.

Information: Works with auxiliary heating option. This modification reduces indoor heating energy or takes longer until the interior is used.

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on“Select”, then click on“18 – Auxiliary heating”.

4 – Click on “Coding – 07” then “Long Coding Helper”

5 – Select Byte 0:
Uncheck Bit 3

L’article A5 (8T) – Engine preheat activation est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera after installation (retrofit camera standard aftermarket or dynamic line camera with camera high module).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 (Camera standard and high):

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 35
Then check Bit 4: “Parking Aid: Rearview Camera installed/active via BCM1 [PR-7X7/7X8]”.

If bit 4 is hidden, in the hexa (yellow digit) if you have 24, change to 34.

Line 2 and 3 only for High camera with module in trunk!

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 7
Then check Bit 1: “Menu Back Up Camera Active”.

Line 3:

3 – Click on“Select” then click on“19 – CAN Gateway”.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Reboot MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed under the screen (Audi Multimedia).

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 11 = video line
Pin 5 = shielding

L’article A5 (8T) Facelift – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera (Standard RVC) after retrofit.

Please note: Reversing radars and MMI 3G are required.
Only A5 8T phase 1, coding for Facelift


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“10 – Parking assistance”.

4 – Click on“Security Access – 16” then type the code“71679”

5 – Click on“Coding – 07” then click on“Long Coding Helper”

6 – Choose byte 0
Then check bit 5 “Rear View Camera installed”.

bit 4 must be set normally (radar on MMI)

Reboot MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed under the screen (Audi Multimedia).

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 11 = video line
Pin 5 = shielding

L’article A5 (8T) – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose : displays automatic speed selection in D and S modes on the on-board display.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “02 – Auto Trans”. 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation – 10”.

5 – Then select “Single Gear Display” from the drop-down list

Set value to “D on/S on

L’article A5 (8T) – Activate automatic speed selection on ODB est apparu en premier sur VAG Coding.