Purpose: Allows the windows to be slightly ajar when the driver’s or passenger’s door is open. When a window is lowered, the cabin is no longer completely sealed, allowing the doors to be closed gently without having to slam them shut. (Windows Auto Drop)


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“


Line 2:

3 – Click “Select,” then click “42 – Driver’s Door.”

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“

L’article A4 (B9) – Enable automatic window lowering est apparu en premier sur VAG Coding.

Purpose: Enables the “recirculation” setting memory. If you have enabled it, it will remain active the next time the vehicle is started. Please note that your Audi has an automatic recirculation function via the MMI system; when this is enabled, the recirculation indicator light does not illuminate while the function is active.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC”.

4 – Click on “Adaptation – 10”.

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “IDE01476 – Store air recirculation setting with terminal 15 off“

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Storing” or “Save,” then confirm.

L’article A4 (B9) – Enable the air recirculation memory function est apparu en premier sur VAG Coding.

Purpose: Displays the intermediate km/h scale on the Virtual Cockpit speedometer. (Works only when the speedometer scale is set to km/h)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – instruments“.

4 – Click on“Coding – 07“, then on“Long Coding Helper“.

5 – Select byte “18“
. Then check bit “1“: “Tachometer_erweiterte_Skalenteilung”

OBDeleven: Tachometer_advanced_scale_division -> yes

L’article A4 (B9) – Display intermediate speeds in the Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: Allows you to unlock certain multimedia system menus while driving, and to enable text entry for CarPlay and Android Auto, which are normally disabled when the vehicle is in motion.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” Select “, then click on ” Select “. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.5F – Information Electr.” .

4 – Click “Adaptation – 10.”

Line 1 (Menu)

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Locked menu contents” (FB CAR, media, and nav)

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “non_blocked” and then confirm.

Line 2

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “NHSTA Properties“

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “not_activated” and then confirm.

Line 3 (CarPlay)

5 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_limitation_switches_for_carplay_no_softKeyboard“

6 – On this same page, there is a second drop-down menu further down
the page.
From this menu, select “not_activated” and then confirm.

Line 4 (Android Auto)

5 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_limitation_switches_for_androidauto_no_text_input“

6 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “not_activated” and then confirm.

L’article A4 (B9) – Unlocking the menus while driving est apparu en premier sur VAG Coding.

Purpose: Disables the feature that automatically unlocks all doors when the DSG automatic transmission is shifted to the “P” position.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

3 – Click on “Select” then click on ” 46 – Central Module Comfort System “ .

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Clear the bit ” automatic_unlock_nar”

L’article A4 (B9) – Disable automatic door unlocking with DSG in “P” est apparu en premier sur VAG Coding.

Purpose: to deactivate/activate the electric handbrake in maintenance mode in order to change/replace the rear brake pad/disc linings. (Lining change mode)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


To begin, set the gearshift to P and remove the electric handbrake on the button. Check that there are no faults/errors before starting basic adjustment.

3 – Click on“Select” then click on“03 – ABS brake“.

4 – Click on“Basic setting – 04“.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Start trim change mode.“

6 – Click on“Go“.

A fault message will appear on your ODB indicating ” Parking brake fault“, but this is normal and should be ignored

7 – Wait for the display“Procedure complete“

8 – Once finished, return to the program until it closes

9 – Switch off the vehicle’s ignition, then disconnect the VAG-COM cable

10 – Change the linings on both sides!

To reactivate the electric handbrake :


11 – With engine off and ignition switched off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

12 – Switch on the ignition and run the VCDS program.

13 – Click on“Select” then click on“03 – ABS brake“.

14 – Click on “Basic setting – 04“.

15 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“End trim change mode.“

16 – Click on“Go“.

17 – Wait for“Procedure complete” display

L’article A4 (B9) – Deactivate/activate electric handbrake for rear brake pad change est apparu en premier sur VAG Coding.

Purpose: Enables full opening of the sunroof when opening with the remote control.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“CA – Open roof”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Position cible pour ouverture confort” /“Komfortfunktionen-Ziellage bei Komfortöffnen”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose “Pos. couliss. “then validate.

L’article A4 (B9) – Full opening of sunroof with remote control est apparu en premier sur VAG Coding.

Purpose: To deactivate the roller blind comfort function when locking/unlocking.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 (Deactivate roller blind when comfort is locked) :
The roof roller shutter is closed when the comfort system is closed. You can adjust this behavior so that the roof roller shutter remains in the current position.

3 – Click on “Select”, then click on “CA – Open roof”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“IDE11842-MAS13330-Komfortfunktionen-Komfortschließen Dachrollo” /“Comfort functions – Roof blind comfort closure”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose “No Active”. No Active “then confirm.

Line 2 (Deactivate roller blind when comfort is opened):
The roof roller shutter is opened when the comfort system is opened. You can adjust this behavior so that the roof roller shutter remains in the current position.

3 – Click on “Select”, then click on “CA – Open roof”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“IDE11842-MAS13329-Komfortfunktionen-Komfortöffnen Dachrollo” /“Comfort functions – Comfort opening roof blind”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select “No Active” and confirm.

L’article A4 (B9) – Deactivate roller blind when locking/unlocking est apparu en premier sur VAG Coding.

Purpose: to adjust the selectable modes of the air-conditioning system. Depending on the vehicle or model year, either the “ECO” or “MAX” air-conditioning mode is activated. You can activate the other mode.

Note: Unfortunately, both modes are not possible at the same time.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” and then click on ” “.08 – Air conditioning“.

4 – Click on“Coding – 09”.

5 – Select byte 8
Enable (for AC Eco) or Disable (for AC Max) bit 1 “ACmax/ECO”.

AC-ECO mode active :

AC-MAX mode active :

L’article A4 (B9) – Air-conditioning mode settings est apparu en premier sur VAG Coding.

Purpose: to disconnect air-conditioning mode from DriveSelect. By default, the air-conditioning mode (ON/OFF/ECO) is coupled to DriveSelect. This means that the air-conditioning system is always activated as soon as you select a new vehicle mode in DriveSelect. You have the option of deleting this pairing, after which the air-conditioning mode always remains in the mode you have chosen.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway”.

4 – Click on“Coding – 09”.

5 – Select byte 15 then disable bit 1 “CHA_Function_KL”.

L’article A4 (B9) – Deactivate air conditioning mode with DriveSelect est apparu en premier sur VAG Coding.